E3NX-MA

Интеллектуальные оптоволоконные усилители

Двухканальный усилитель требует в два раза меньше пространства для монтажа, чем уменьшает размеры оборудования и шкафов управления.

Новый 2-канальный оптоволоконный усилитель выполняет работу двух блоков при размерах одного, способствуя уменьшению размеров вашего оборудования и шкафов управления.
Высокие характеристики и стабильность обнаружения, даже при двух каналах. От прозрачных объектов до поверхностей с плохим отражением.
Простая автоматическая настройка интенсивности света и пороговых значений.
Модели с разъемами с уменьшенным числом проводов сокращают монтажные работы.

Logic operations without PLC

Логические функции AND (И), OR (ИЛИ), XOR (исключающее ИЛИ) и GAP между обоими каналами позволяют выполнять элементарную обработку сигналов без необходимости в ПЛК. Это дополняет функционал датчиков непосредственно на машине без перепрограммирования ПЛК.

Space & cost reduction

Усилитель 2 в 1 заменяет собой два стандартных усилителя и обеспечивает экономию пространства и затрат на оборудование.

Ordering information

Type		Connecting method	Appearance	Inputs/outputs	Order code
Type		Connecting method	Appearance	Inputs/outputs	NPN output	PNP output
2-channel models	Standard Type	Pre-wired (2 m)		2 outputs	E3NX-MA11	E3NX-MA41
	Standard Type	Wire-saving Connector		2 outputs	E3NX-MA6	E3NX-MA8
	Model for Sensor Communications Unit1	Connector for Sensor Communications Unit		−	E3NX-MA0

Specifications

Type		Standard Type		Model for Sensor Communications Unit
NPN output		E3NX-MA11	E3NX-MA6	E3NX-MA0
PNP output		E3NX-MA41	E3NX-MA8	E3NX-MA0
Connecting method		Pre-wired	Wire-saving Connector	Connector for Sensor Communications Unit
Inputs/outputs	Outputs	2 outputs		−2
Inputs/outputs	External inputs	−	−	−2
Light source (wavelength)		Red, 4-element LED (625 nm)
Response time	Super-high-speed mode (SHS)	Operate or reset: 100 μs
	High-speed mode (HS)	Operate or reset: 450 μs
	Standard mode (Stnd)	Operate or reset: 1 ms
	Giga-power mode (GIGA)	Operate or reset: 16 ms
Sensitivity adjustment		Smart Tuning (2-point tuning, full auto tuning, position tuning, maximum sensitivity tuning, power tuning, or percentage tuning (-99% to 99%)) or manual adjustment
Maximum connectable Units		30		With E3NW-ECT: 30 units3 With E3NW-CCL: 16 units
No. of Units for mutual interference prevention4 5		9
Functions	Automatic power control (APC)	Always enabled.
	Dynamic power control (DPC)	Provided
	Timer	Select from timer disabled, OFF-delay, ON-delay, one-shot, or ON-delay + OFF-delay timer: 1 to 9,999 ms
	Zero reset	Negative values can be displayed. (Threshold value is shifted.)
	Resetting settings 6	Select from initial reset (factory defaults) or user reset (saved settings).
	Eco mode	Select from OFF (digital display lit), Eco ON (digital display not lit), and Eco LO (digital display dimmed).
	Bank switching	Select from banks 1 to 4.
	Power tuning	Select from ON or OFF.
	Output 1	Select from normal detection mode or area detection mode.
	Output 2	Select from normal detection mode, AND output mode, OR output mode, XOR output mode, GAP output mode, Falling synchronization mode, Rising synchronization mode or area detection mode.
	Hysteresis width	Select from standard setting or user setting. For a user setting, the hysteresis width can be set from 0 to 9,999.
Ambient illumination (Receiver side)		Incandescent lamp: 20,000 lx max., Sunlight: 30,000 lx max.
Ambient temperature range7		Operating: Groups of 1 or 2 Amplifier Units: −25 to 55°C, Groups of 3 to 10 Amplifier Units: −25 to 50°C, Groups of 11 to 16 Amplifier Units: −25 to 45°C, Groups of 17 to 30 Amplifier Units: −25 to 40°C Storage: −30 to 70°C (with no icing or condensation)		Operating: Groups of 1 or 2 Amplifier Units: 0 to 55°C, Groups of 3 to 10 Amplifier Units: 0 to 50°C, Groups of 11 to 16 Amplifier Units: 0 to 45°C, Groups of 17 to 30 Amplifier Units: 0 to 40°C Storage: −30 to 70°C (with no icing or condensation)
Ambient humidity range		Operating and storage: 35 to 85% (with no condensation) within the surrounding air temperature range shown above
Insulation resistance		20 MΩ min. (at 500 VDC)
Vibration resistance (destruction)		10 to 55 Hz with a 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance (destruction)		500 m/s² for 3 times each in X, Y, and Z directions		150 m/s² for 3 times each in X, Y, and Z directions
Degree of protection		IEC 60529 IP50 (with Protective Cover attached)
Weight (packed state/Sensor only)		Approx. 115 g/ approx. 75 g	Approx. 60g/ approx. 20g	Approx. 65 g/ approx. 25 g
Materials	Case	Polycarbonate (PC)
	Cover	Polycarbonate (PC)
	Cable	PVC

1. A Sensor Communications Unit is required if you want to use the Fiber Amplifier Unit on a network.

2. Two sensor outputs are allocated in the programmable logic controller PLC I/O table.
PLC operation via Communications Unit enables reading detected values and changing settings.

3. When connected to an OMRON NJ-series Controller.

4. The tuning will not change the number of units.
The least unit count among the mutual interference prevention units of E3NX and E3NC.
Check the mutual interference prevention unit count and response speed of each model.

5. The mutual interference prevention function is disabled if the detection mode is set to super-high-speed mode.