F3SJ-B

Базовая серия с оптимальным соотношением характеристик и возможностей
Семейство F3SJ-B — это световые барьеры безопасности типа 4 с разрешающей способностью 25 мм. Ширина барьера достигает 7 м, высота варьируется в пределах от 185 до 2065 мм, мертвая зона отсутствует.
- Высота барьера = длина датчика
- Простая защита кистей рук
- Функция селективного пропуска
- Последовательное соединение до трех барьеров
- Датчик типа 4 в соответствии со стандартом EN 61496-1, уровень эффективности (PL) вплоть до «e» согласно EN ISO 13849
Ordering information
Protective height (mm)1 | ||
---|---|---|
Accessories (sold separately)
Single-end connector cable (2 cables per set, for emitter and receiver)
For wiring with safety circuit such as single safety relay, safety relay unit, and safety controller.
![]() | |||
Sensor mounting bracket
![]() | ||||
![]() | ||||
![]() | F39-LJB3-M61 | |||
F39-LJB3-M82 | ||||
![]() | Bracket to mount an intermediate bracket to the aluminum frame | F39-LJB3-M6K1 | ||
F39-LJB3-M8K2 | ||||
![]() | Mounting bracket used when replacing existing area sensors | |||
![]() |
Laser pointer
![]() |
Specifications
Setting tool connection4 | |||
Operating range5 | |||
15 ms max. (response time at 1 set connection, series connection of 2 sets or 3 sets) | |||
70 ms max. (response time at 1 set connection, series connection of 2 sets or 3 sets) | |||
Emitter: Up to 22 beams: 52 mA max., 26 to 42 beams: 68 mA max., 46 to 62 beams: 75 mA max., 66 to 82 beams: 88 mA max., 86 to 102 beams: 101 mA max. Receiver: Up to 22 beams: 45 mA max., 26 to 42 beams: 50 mA max., 46 to 62 beams: 56 mA max., | |||
Based on IEC 61496-2. Within ±2.5° for both emitter and receiver when the detection distance is 3 m or over | |||
Two PNP transistor outputs, load current 200 mA max., residual voltage 2 V max. (except for voltage drop due to cable extension), Leakage current 1 mA max., load inductance 2.2 H max.6, Maximum capacity load 1 μF7 | |||
One PNP transistor outputs, load current 100 mA max., residual voltage 2 V max. (except for voltage drop due to cable extension), leak current 1 mA max. | |||
Safety output: On when receiving light | |||
ON voltage: Vs-3 V to Vs, OFF voltage: 0 V to 1/2 Vs or open8 | |||
Mutual interference prevention algorithm prevents interference in up to 3 sets. | |||
Time division emission by series connection Number of connections: up to 3 sets (between F3SJ-Bs only)Other models cannot be connected. | |||
Output short-circuit protection, and power supply reverse polarity protection | |||
Operating: 35% to 85% (no condensation), Storage: 35% to 95% RH | |||
Malfunction: 10 to 55 Hz, Multiple amplitude of 0.7 mm, 20 sweeps in X, Y, and Z directions | |||
Malfunction: 100 m/s2, 1,000 times each in X, Y, and Z directions | |||
Connection method: Prewired connector cable, cable length 0.3 m, connector type (M12, 8-pin), connector: IP67 rated (when mated) | |||
Test rod, Instruction manual, User's manual (CD-ROM)9 | |||
IEC 61496-1, EN 61496-1 UL 61496-1, Type 4 ESPE (Electro-sensitive protective equipment) IEC 61496-2, CLC/TS 61496-2, UL 61496-2, Type 4 AOPD (Active opto-electronic protective devices) IEC 61508-1 to -3, EN 61508-1 to -3 SIL3 |
Connections
Basic Wiring Diagram
Wiring when using manual reset mode, external device monitoring (F3SJ-B ____ P25) (PNP output)

6. The load inductance is the maximum value when the safety output frequently repeats ON and OFF. When you use the safety output at 4 Hz or less, the usable load inductance becomes larger.
6. The load inductance is the maximum value when the safety output frequently repeats ON and OFF. When you use the safety output at 4 Hz or less, the usable load inductance becomes larger.