приводы Accurax G5

В сердце движения
Сервосистема Accurax G5 дает вам преимущества, которые необходимы для создания более точного, более быстрого, более компактного оборудования. Благодаря снижению массы двигателя почти на 25% и сокращению занимаемого в шкафу места на 50% перед вами открываются новые возможности. Это и субмикронная точность, и время стабилизации порядка миллисекунд.
- Модели сервоприводов EtherCAT, ML-II и аналоговых/импульсных сервоприводов
- Соответствие безопасности ISO13849-1 PL-d
- Высокая частота пропускания 2 кГц
- Высокое разрешение обеспечено 20-битным энкодером
- Программирование привода: встроенная функциональность позиционирования в аналоговых/импульсных моделях
- Внешний вход энкодера для полной обратной связи
- Автонастройка в реальном времени
- Современные алгоритмы управления (функция подавления вибрации, упреждающее управление по моменту, контроль возмущения)
Ordering information
Accurax G5 series EtherCAT reference configuration

Note: The symbols ① ② ③ ④ ⑤ ... show the recommended sequence to select the components in Accurax G5 servo system
Servo motors, power and encoder cables
Note: ① ② Refer to the Accurax G5 servo motor chapter for servomotor, motor cables or connectors selection
Servo drives
Signals cables for I/O general purpose (CN1)
External encoder cable (CN4)
Analog monitor (CN5)
USB personal computer cable (CN7)
Cable for safety (CN8)
EtherCAT controllers
External regenerative resistor
Filters
0.3 mA/32 mA1 | |||||
0.3 mA/32 mA1 | |||||
0.3 mA/32 mA1 | |||||
0.3 mA/40 mA1 | |||||
2 mA/130 mA1 |
Connectors
Computer software
SYSMAC-SE2___2 | |
Note: If CX-One is installed on the same computer as Sysmac Studio, it must be CX-One v4.2
or higher.
Accurax G5 series MECHATROLINK-II reference configuration

Note: The symbols ① ② ③ ④ ⑤ ... show the recommended sequence to select the components in Accurax G5 servo system
Servo motors, power and encoder cables
Note: ① ② Refer to the Accurax G5 servo motor section for servomotor, motor cables or connectors selection
Servo drives
Control cables (CN1)
External encoder cable (CN4)
Analog monitor (CN5)
MECHATROLINK-II cables (CN6)
MECHATROLINK-II motion controllers
USB personal computer cable (CN7)
Cable for safety functions (CN8)
Safety connector with 3 m cable |
External regenerative resistor
Filters
0.3 mA /32 mA3 | |||||
0.3 mA /32 mA1 | |||||
0.3 mA /32 mA1 |
Connectors
Computer software
Accurax G5 series analog/pulse reference configuration

Note: The symbols ① ② ③ ④ ⑤ ... show the recommended sequence to select the components in Accurax G5 servo system
Servo motors, power and encoder cables
Note: ① ② Refer to the Accurax G5 servo motor section for servomotor, motor cables or connectors selection
Servo drives
Servo drive models4 | |||||
---|---|---|---|---|---|
Control cables (CN1)
External encoder cable (CN4)
Analog monitor (CN5)
USB personal computer cable (CN7)
External regenerative resistor
Cable for safety functions (CN8)
Safety connector with 3 m cable |
Filters
0.3 mA/32 mA5 | |||||
0.3 mA/32 mA1 | |||||
0.3 mA/32 mA1 | |||||
0.3 mA/40 mA1 | |||||
2 mA/130 mA1 |
Connectors
Computer software
Specifications
Single-phase, 230 V
Single-phase/3-phase, 200 to 240 VAC + 10% to −15% (50/60 Hz) | |||||||||
5.88 m/s2 10−60 Hz (Continuous operation at resonance point is not allowed)/19.6 m/s2 | |||||||||
Three-phase, 400 V
5.88 m/s2 10−60 Hz (Continuous operation at resonance point is not allowed)/19.6 m/s2 | |||||||||||
Dimensions
CX-Drive

CX-One

Sysmac Studio
