Серия KM1

Многоканальный монитор с интеллектуальным управлением
Платформа KM1 позволяет визуализировать потребление электроэнергии при использовании на задней панели с помощью концепции "ведущий-ведомый". К ведущему блоку можно подключить до четырех ведомых для осуществления одновременного измерения электрических и неэлектрических параметров.
- Существенно сокращено время установки.
- Пространство для установки уменьшено на 24% по сравнению с традиционными средствами для контроля.
- Уменьшено количество устройств: с помощью одной платформы можно измерить до 36 контуров.
- Количество проводных соединений также уменьшено благодаря высокоскоростному соединению внутренней шины Innerbus и напряжению источника питания ведущего блока.
- Настраиваемая платформа для любой области применения
- Удобная классификация объединенной энергосистемы благодаря настраиваемым внутренним пороговым значениям
- Высокоточные измерения даже для токов ниже 5% от номинального значения.
- Отсутствие необходимости использовать трансформатор напряжения / До 7 импульсных выходов для сбора данных, в том числе, о неэлектрических параметрах
- Оснащен входом температуры
- Бесплатная программа для конфигурации KM//KE1
- Двойной мониторинг системы с помощью одного блока
Ordering information
Smart power monitors
Options (Order separately)
Separate or In-panel current transformer (CT)
Note: CT cables are not included with the CTs.
Current transformer (CT) cable
Note: Use the CT cable specified by OMRON or one manufactured by JST Mfg. Co.
You can also use a 1.25-B3A crimping terminal or AWG22 power cable.
Related devices (Sold separately)
Communications interface converter
Specifications
Ratings
Performance
Accuracy1 | ±1.0% FS, ±1 digit; or, ±2.0% FS, ±1 digit for voltage across Vtr under the same conditions | ||||
However, the accuracy is ±2.0% FS, ±1 digit for the phase-S current for a three-phase, three wire circuit and the phase-N current for a single-phase, three wire circuit under the same conditions. | |||||
However, the accuracy is ±2.0% FS, ±1 digit for the phase-S current for a three-phase, three wire circuit and the phase-N current for a single-phase, three wire circuit under the same conditions. | |||||
Power factor2 | ±5.0% FS at an ambient temperature of 23° C, rated input, rated frequency, and a power factor of 0.5 to 1 to 0.5 | ±5.0% FS at an ambient temperature of 23° C, rated input, rated frequency, and a power factor of 0.5 to 1 to 0.5 | |||
±5°C two hours after the power supply is turned ON (after performing any adjustments for the ambient temperature) | |||||
CompoWay/F: 0 to 99, Modbus:1 to 99 When a switch operation is performed to set the protocol to Modbus when the node number is set to 0, the node number is automatically changed to 1. | |||||
Data length3 | |||||
Stop bits3 | CompoWay/F: 1 bits or 2 bits; Modbus: 1 bit with priority, 2 bits without priority | ||||
Special CTs
Current Transformer (CT) Cable
KM-series Power monitor models
(maximum width of 45 × 5 when five Units are linked together) | ||||
KE1-DRT-FLK DeviceNet communications unit
Can be a combination of multidrops and T-branching (for both main and branch lines). | ||||
5 dedicated lines (2 signal lines, 2 power lines, and 1 shield) | ||||
Maximum network length4 | ||||
1. Based on JISC1111, without special CT error, at ambient temperature of 23° C, rated input, and rated frequency. Applicable to 2nd, 3rd, 5th, 7th, 9th, 11th, and 13th harmonics.
1. Based on JISC1111, without special CT error, at ambient temperature of 23° C, rated input, and rated frequency. Applicable to 2nd, 3rd, 5th, 7th, 9th, 11th, and 13th harmonics.
Брошюры
Показать все БрошюрыРуководство по подключению
Показать все Руководство по подключениюТехнические руководства
Программное обеспечение

EasyKM-Manager Программное обеспечение
Пожалуйста, войдите или получите прямой доступ к скачиванию данного документа

KM-KE setting Программное обеспечение
Пожалуйста, войдите или получите прямой доступ к скачиванию данного документа